WBX Enclosure Assembly

This section explains the techniques for setting up the protective enclosure that surrounds a Cyberware Whole Body X Color 3D Digitizer.

For a Whole Body Color X 3D Scanner (Model WBX), you must complete the software installation procedure for USB-based scanners before continuing.

WARNING:

Many of the parts are very heavy and very sensitive; care and proper equipment should be used to put them in place. Many of the parts contain either carefully aligned or sensitive electronic assemblies. Take extreme caution not to damage or jar the systems. It is required that, at least, 4 able-bodied persons are available to assemble this platform effectively. Always lift carefully using proper lifting techniques. Improper lifting without qualified help may result in serious injury.

Cyberware recommends that you keep ALL of the shipping boxes and packing materials that came with the scanner. These are useful if you should wish to move the system or store the system for an extended period of time.

Required Tools

• M5 Hex Wrench
• M6 Hex Wrench
• Modified M6 Hex Wrench
• Small Flathead Screwdriver

Procedure

1. Disconnect the power supply AC cord from the surge protector.
2. Manually raise arm 0&1 and arm 2&3 so that they are out of the way and will not become an obstruction during the remaining assembly steps.
3. Place the (2) two platform halves over the main truss. Ensure that platform 0/1 is parallel to the platform legs.

WBX Enclosure Installation

4. Place the subject platform/weigh scale into place between the (2) two platform halves.
5. Install the (2) two kick panels to connect the (2) two platform halves and protect the subject platform/weigh scale.
6. Install the first interior panel. Use (4) four large lag screws to attach the interior panel to the platform half.

WBX Enclosure Installation

7. Install the second interior panel. Use (4) four large lag screws to attach the interior panel to the platform half.

WBX Enclosure Installation

8. Use (6) six long screws and (1) one small screw each to join the window panels to the inside panels (unbolt window clamps on interior side of window panel [side without plastic panel]). Save the nuts for later use in case of the need to transport or store the scanner.
9. Attach the side panels to the platform halves using the M6 × 35 screws and washers.

WBX Enclosure Installation

10. Install the arches between the side panels using the M6 × 35 screws and washers.
11. Place the panel spacers (2 — one at each tower) so that the spacer touches the interior platform half.
12. Install the H1 corner panel.
13. Install the H1 back panel.
14. Install the H0 corner panel.
15. Install the H0 back panel.
16. Slide the H0 and H1 back panels together (some force may be required to achieve proper mating between the panels), then connect them using the appropriate screws.
17. Install the H3 corner panel.
18. Install the H3 back panel.
19. Install the H2 corner panel.
20. Install the H2 back panel.

WBX Enclosure Installation

21. Slide the H2 and H3 back panels together (some force may be required to achieve proper mating between the panels), then connect them using the appropriate screws.
22. Install the (2) two top cross members using the appropriate screws.

WBX Enclosure Installation

23. Place the (3) three top enclosure panels into their respective positions as the ceiling of the enclosure.
24. If not already done, connect all cables to the scanner's power supply (through the hole in the enclosure).
25. Place the power supply into position in the enclosure.
26. Secure the power supply unit to the enclosure using four (4) ¼-20 × ¼ screws and washers.
27. Plug the power supply AC cable into the surge protector.
28. Turn on the power by turning the system control switch past the On position to Enable, then back to the On position.
29. Power ON the workstation.

The scanner is now ready for use.

Consult the tutorials in this user guide for information on how to operate this scanner.